Innokin Sensis 40W

Introduction

 

It’s time for one of the most revolutionary devices in the vape world, the Innokin Sensis 40W Pod Mod Starter Kit. A Classy-looking device comes with a glass tank that you can pop on a 510 connection. With 4th Gen vape tech included that gives an upgrade in the technology of Innokin Sensis 40W. This upgrade boosts flavors and extends coil life.

“Find F” mode also, is one of the modes that gives this device a high rating and makes it more powerful and exciting to use. In the next sections, I’m going to put more lights on this new technology. So, please keep reading vapors.

Also, it is eco-friendly, it’s made of 100% recycled materials, wattage range from 6 to 40 watt. Its tank holds 3.1 ML of e-liquid, bottom fill, 510 Drip tip.

 

Inside Innokin Sensis 40W box

 

• Sensis Pod Mod
• 3.1mL Sensis Cartridge
• 0.25-ohm Scepter-S Coil, a preinstalled coil, kanthal, and the wattage range between 25W-35W.
• 0.65-ohm Scepter-S Coil, for MTL vaping, kanthal, and the wattage range from 9-12 watts.
• MTL Drip Tip
• 2 x O-Rings
• Coil Connector
• 510 Adapter
• Type-C USB Cable

Note: Replacement coils come with five coils but it comes with only the coils, you need to keep the base.

                                 

 

Innokin Sensis 40W specs & features

 

• Integrated 3000mAh Rechargeable Battery
• Wattage Output Range: 6-40W
• Mode (Wattage, Voltage, and Bonus F0)
• Zinc-Alloy Chassis Construction
• 3.1mL Glass Pod Capacity
• Bottom Fill System – Silicone Stoppered
• Innokin Scepter-S Coil Series
• Press Fit Coil Installation
• Magnetic Pod Connection
•  Protections (Low Battery, Vaping Overtime, Overheat, Short-Circuit, and Low Resistance)

 

Innokin Sensis 40W Menu

Main Functions

• To turn the device on/off, click on the power button three times.
• To adjust the wattage, click on the up/down button and hold it until it’s blinking then adjust the wattage as you want.
• On the main screen, you have wattage, buff timer, Resistance of the coil, buff counter, and voltage.
• Clicking on the Down and fire button at the same time would lock the screen.
• Clicking on the up button and fire button will give you a status about your device.

 

 

Menu Settings

• To get into the menu you would need to click on up and down at the same time.
• In the setting menu, you would find “power, coil+, refresh, lock, setting and exit”
• You can choose between voltage and Wattage, coil + would activate the coil+ mode, in Power.
• In refresh you would get to get your coil back a bit, there are two modes, Run once Auto and the extended hold.
• In Auto, the device will send a signal to the coil for four seconds.
• The extended mode would send the signal as long as you press it for a max of nine seconds cap and get out you just press exit.

 

Options

You would have six options, operating screen, Timeout, Cutoff, Device ID, Reset, and exit in the settings menu.

• The operating screen would change the looks of the main screen, you have two options Minimal or pro.
• Timeout is the time your screen will stay led for after you release the button from 5 seconds up to 180 seconds.
• The cutoff is the time of your puff, you have a minimum of three seconds up to 18 seconds.
• The device ID is going to give you your device ID and Reset will reset the device back to its factory settings.

 

 

What is the purpose of the three functions: refresh, coil+, F0?

 

It improves the coil life and flavor as I mentioned earlier in our introduction. So, let’s dig more vapors.

Coil+ is designed to increase the coil life, Refresh is designed to bring your coil back a little bit while F0 is designed to improve flavor a bit and increase the coil life. Coil+ it fires like a standard wattage and after you release it give the coil a little wiggle.” increase the coil life”. For starts as a standard wattage than an AC signal or sinewave, shake or wiggle all the time. “increase the coil life and enhance flavor”.

                           

Refresh is designed for enhancing flavor by vibrating the coil or clean the coil a little bit, by generating a little bit of heat which increases the coupling reaction of the coil pulls more e-liquid and refreshes the coil.

                                   

 

What is the F0 function?

 

F0 is a function that is designed to restore coil and flavor.

 

How to activate the F0 function?

 

Activation Methods

When you open your device for the first time it will show a lock symbol on your main screen and I would show you some codes in this article that might work out for you. Just follow one of the next steps to activate it.

• 1- -+-++- (fire)
• You could just take 6000 puffs and it will unlock automatically
• You could join the Facebook group.

 

How to login into F0

1. From the main menu select F0.
2. Choose your frequency.
3. Press fire.

                                   

                                      

 

 

Innokin Sensis 40W FAQs

 

How do F0 works?

By vibrating the coil via AC signal, it has a range from 25 HZ to 416 HZ.

                               

 

Why this range of frequency in the F0 function?

Well, it depends on the coil, the lower the gauge the higher the frequency.

 

Do I have to use the pods and the coils that come with the package to get used to the technology?

No, You can use any coil or tank via the 510 connectors to take advantage of the technology.

 

Innokin Sensis 40W Verdict

 

To sum up our review about Innokin Sensis 40W, There is no doubt this is a new technology and it has a lot to offer, Innokin Sensis 40W has a very distinct function when it comes to clean the coil.

We would recommend this device for new and current vapor. It is going to give you the experience you want and the excitement also. It brings new technologies that blow our minds, What an interesting device vapors.

Buy it from Vaporfi

Read more reviews

• Dotmod Dot box 220
• Black Panther MTL by Dr Vapes